15 Of The Best Pinterest Boards All Time About Door Lock Change > 자유게시판

How to Do a Door Lock Change

Change your door lock is a simple and affordable way to improve the security of your home. However, this process is not for all. It requires some skill and perseverance.

You need to replace the cylinder that is within the knob's body. The cylinder is responsible to recognize the key when it is put into the lock.

Removal of the old lock

First, you must remove the lock you have been using for a while. This is a relatively easy process, but there are some things to remember. Make sure that the new lock fits your door. This will ensure it is secure and doesn't leave a gap in the deadbolt or latch.

After you have removed the latch plate, you'll need to look for two bolts or screws in the casing's interior that are holding the casing together with the lock halves. Remove them with a screwdriver, then take the lock out of the door. If you have a mortise lock there might be a set screw at the base of the handle that holds it to the spindle. Remove the doorknobs by unscrewing this screw using a screwdriver.

It is also recommended to remove the latch and deadbolt plug from the hole in your door jamb. Then, you can put in your new lock. If you are replacing a mortise lock, you should also measure the distance between the lock case and the door's edge to ensure that your new lock will be able to fit.

It is possible to replace your lock for a variety of reasons, such as the possibility that someone else holds the key, or if you have an incoming roommate. You could save money if you remove the lock yourself instead of hiring an expert. The process is easier than most people think, and it can be completed in just a few minutes.

Remove the trim and handle of your door. Then, pull the trim loose using a screwdriver that is flat. You should be able twist off the majority of it. In some cases you might be able to remove the handles completely. Then, check the handle for a small pinhole on the inside. Then insert a straightened clip into it. This will trigger the release mechanism and allow you to take the handle from the door. Then, look for another small tab in the interior of the lock and push it with a flat screwdriver. Once the spindle is removed, you can take off the cylinder and housing.

The choice of a new locking system

You have many options when it comes to selecting a new lock. Consider the different types of locks and select one that fits the style of your door. Consider the backset (the distance between the edge of the door and the center of the lock hole) and the cross bore (small hole in the frame of the door frame). Also, ensure that you choose a lock that will accommodate the door's thickness as well as swing.

The majority of door locks have been assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they will withstand use and how difficult they are to pick or disable. A grade 3 upvc window lock repairs near me may be ideal for a peaceful apartment building in the countryside, whereas repair window locks upvc of grade 1 may be better suited to the busy streets near an open-air storefront.

Most smart door locks require digital code to open. If you are worried about hacking or other security issues, talk to an expert locksmith.

Replacing the cylinder

If your door lock's cylinder is broken or damaged, you can replace it within a matter of minutes using a simple DIY project. It is important to select the appropriate cylinder and follow all instructions. The first step is to take off the knob or handle, should there be one and then remove the trim that is attached to the base of the lock cylinder by using a screwdriver. Once the trim is removed, you can reach the screws that keep the cylinder in place and remove them with a flathead screwdriver. The cylinder is then gently pulled from the door.

Be sure to measure the length of your new cylinder before installing it. With a tape measure, determine the distance between the cylinder's center and the left and right sides. Purchase a new cylinder which has the same measurements. This will prevent cylinders from snapping when doors are kicked or the key gets stuck inside.

If you have a suitable replacement upvc window locks cylinder, place it in the door and turn the key. This will align the cylinder with your carrier which is located usually on the outside of your lock. Then, you can loosen the set screw that should be just a few turns inside the head. You will also need to loosen the screw on the door's edge that fastens the case, should there be one.

You can replace the lock cylinder you have used with the new one by slipping it into the case, and tightening the set screws. Installing the part that connects the cylinder to a lock indicator stem is also essential. You can do this by pulling three tabs at the back of the cylindrical using needle-nosed pliers. Attach the bracket that is smaller to the back of the cylinder. You must then install the latch plate and strike plate, along with the retaining rings connected to the top of the lock cylinder.

Installing a new lock

Begin by measuring the door's width if you are replacing an existing lock. The majority of residential locksets are designed to fit a door thickness of 1 3/8 - 3/4 inches. If your door is thicker, you will need a thick door kit that includes longer screws as well as longer tail pieces (for door knobs) or spindle extension (for deadbolts).

Most locks come equipped with a thorough installation guide to aid you. Read the instructions carefully before starting the process to ensure that you are following all the steps. The booklet will also give you an idea of the level of skill required to complete the task. If you're replacing a lock for the first time, you might want to ask an experienced friend for assistance.

It's a good idea to seal the openings of the old lock before installing the new lock. This will stop screws from slipping through the holes, and also protect any tiles you may have installed. This will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch includes a strip of masking or gaffer tape, however you can make use of any tape you have.

After taking off the screws that connect the lock's interior to its exterior, pull the Window lock replacement straight away. This must be done quickly to avoid the lock from accidentally closing and damaging the mechanism.

If the new lock comes with an internal latch bolt, insert the new bolt into its upper cross bore. Make sure you put it in the correct position, which is indicated by an arrow. Then, you can screw the latch plate onto the bolt.

Finally, screw the deadbolt and strike plate into the door jamb. Test the deadbolt a few times, throwing it around to make sure it extends into the strike plate. Follow the steps that come with your electronic smart lock to program it. This involves downloading an application, registering your email address, confirming your identity, then accessing the wireless network to add your device.